I actually tried this as my second step in trouble shooting, the first being using different ports.

In the non-omada management software, it defaults to 10G, and if the devices is on before the switch it negotiates 10G correctly and works at full speed (tested with iperf3). As soon as any of the 10G connected devices is rebooted, I’m back to 1G. To fix it, I then have to set the port to 1G with flow control on, apply changes, save config, refresh page, change to 10G with flow control off, apply, save config and it goes back to 10G again. Alternatively I can reboot their switch and it’s fine again.

In Omada its the same, fewer steps to get there but I have to sometimes do it 2-3 times before it works.

Same issue with both 10G TP-Link switches, so I’m thinking it might be the SFP. Using Intel SFP+ with FS optical cables. I’m using a DAC for the uplink from the 10G switch to my unmanaged 2.5G switch, and that doesn’t have the problem of dropping, always works max speed.

Oh wow, hard to believe a huge bug like that would make it to production. What do you recommend instead? Stick with TP-Link?

So I just added a TP-Link switch (TL-SG3428X) and access point (EAP670) to my network, using OPNSense for routing. I’m still within the return window for both items. I understand the article mentions routers, but should I consider returning these, and upping my budget to go for ubiquity? The AP would only be like $30 more for an equivalent, so that’s negligible, but a switch that meets my needs is about 1.6x more. And still only has 2 SFP+ ports, while I need 3 at minimum.

Sure could. Unfortunately, those trains don’t run between my home and work, or grocery store, or doctor and hospital, or movie, or the mountains for skiing/camping, or any other amenities where I live. I wish I had great public transit options like in Europe, but I don’t.

Now that’s a great looking car. Could never afford it, but it’s great nonetheless.

I’ll give that a shot, thanks!

Thanks for the detailed reply.

So the command gives me an error that nfs-client cannot be found.

The fstab just has basic default config. No timeout set.

I considered network issues, though it seems to be quite stable for other services. Not ruling it out just yet. I have a new switch coming in the next week, so will test if the issue persists when I put that in.

I will also give autofs a shot.

Thanks!

Haha don’t cut it up just yet! I’ll try some of the other options suggested here, as I’d like to learn what the issue is. The worst case I’ll try smb.

Thank you, will try this when I have time later this week.

They are mounted via the gui, but it just puts the mount into fstab. I checked the config there and it is just the standard default options for an nfs mount.

Edit: and no, I don’t lose it on reboot. Reboot re-mounts the share correctly.

Through the Cockpit gui, which just puts it into fstab. I checked the fstab config and it just has the basic default settings.

Doesn’t seem like it as far as I can tell.

Ya you’re right some of their views are 👎. I actually stopped listening to the podcast sometime over the pandemic when they had a super right wing guest on and they let loose and agreed with his views which was uncommon. Didn’t finish the episode, but came back to it a few years later and I recall hearing Aaron back track. Some of their newer episodes are still interesting and they seem to be more balanced, though I’ve been listening to the pre pandemic episodes.

For me Mysterious Universe takes the cake. A couple of Aussie guys talking about anything and everything paranormal, big foot, lucid dreaming, missing 411, stone tape theory, mediums, hauntings, abductions, time travel, ufos, men in black, remote viewing, alternative history theories, etc. They don’t really delve into conspiracy theories which I appreciate.

They’ve been at it for ages, and they are on season 32 of the regular show and 30 of the plus show (2 seasons per year). Most shows they discover a book or essay and do a deep dive into it, explaining and linking it to other research.

My main draw is how they don’t take anything too seriously, and are able to objectively present a theory about “black ops stealth [person of short stature]”, mixed with “the meaning behind your Thai diving instructor’s tramp stamp”, and follow it by well researched interviews with authors and researchers. Giving facts and letting listeners draw their own conclusions.

All that to say, I’ve listened back to season 11 so far, and have thousands of hours of content. Highly recommend.

I feel like it should be “Jean”, non? If it was a Fiat or an Alfa Romeo, Giovanni would be a great fit. Maybe you have your own context or reasoning though ☺️.

Will do for sure! Going to work on it sometime in May.

Oh wow this is excellent, thank you so much for taking the time to do such a detailed write up! Much appreciated. Going to get everything together this weekend and tackle it over the next few days. Thank you!!

Oh good idea, I never considered that because of how thing the veneer/film is. Would standard wood glue do the trick you think?

I’ve never used an oil based primer, only the bullseye / shellac stuff. Not sure if it’s the same, but seems to seal well.

Nice thanks all, glad that my initial thoughts on repair seem to be on the right track. The cabinets are original and are over 35 years old at this point, so not the worst shape all things considered!

Ah that’s a good tip. I’ll take a look if it’s available locally, it’s like that bondo stuff so probably. I think the wood filler I have is also outdoor grade, and would be covered by sealer/primer. Best to start with a solid layer first though!